Produktai skirti poliuretano gruntas (12)

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

ESCRIPTION Enduit pour reboucher rapidement les fissures, trous et saignées de toutes tailles sans retrait et sans fissuration. COMPOSITION ET ASPECT Enduit en poudre à base de plâtre, carbonate de calcium, charge minérale, cellulose et divers adjuvants. La pâte obtenue est de couleur blanche. SUPPORTS ADMIS Tous types de supports en intérieur bruts ou peints : plâtre, plaques de plâtre, carreaux de plâtre, béton, enduit ciment, agglos, béton cellulaire, briques, terre cuite… CARACTÉRISTIQUES TECHNIQUES • pH : neutre • Temps de prise : 30 minutes en fonction des conditions ambiantes et de l’épaisseur appliquée CONDITIONNEMENT Sacs de 5 et 15 kg. APPLICATION L’application se fait au couteau à enduire. Consommation : 1kg /m²/mm d’épaisseur. TEMPS DE SÉCHAGE Il dépend des conditions ambiantes, de la nature du support et de l’épaisseur d’application. En règle générale, pour un cm d’épaisseur, l’enduit est sec en 6 heures.

Bitumer Flexigum PU ist eine zweikomponentige Bitumen-Polyurethan-Verbindung, die eine dauerhaft flexible und chemisch beständige Befestigungs- und Spannungsübertragungsmasse bildet. Bitumer Flexigum PU findet seinen Einsatz in: •zur dauerelastischen Befestigung der Schiene als Unterboden, •Schienenbefestigungsmasse und als Unterbodenbelag, •zur Herstellung dauerhafter und flexibler Dehnungsfugen zwischen Betonplatten und Elementen aus Stahl, •Ausfüllen der Lücken zwischen Fahrbahn und Schiene, •zum Füllen von Beton-Beton-Fugen •Verfüllen von Fugen, Lücken, Rissen und Dehnungsfugen in stark bearbeiteten Asphalt- und Betondecken (z. B. Bordsteine ​​auf Brücken), •Verfüllen von „arbeitenden“ Fugen auf Stahl- und Betonbrücken und anderen Gehwegen, die durch starke Bewegungen gekennzeichnet sind.

SOLVENT PAINT of COSMOCHROME is a high quality undercoat for concrete surfaces (concrete columns, concrete floors, walls, ceramic tile roofs etc). It is highly durable against extreme weather conditions and atmosphere pollution. It has strong adhesion, great covering power and extreme hardness PACKAGE:0,75 LT, 10 LT, 2,5 LT COLOR:Black, Cypress Green

TECHNICAL SPRAYS

Anstrichverträglicher Einkomponenten-Dichtstoff auf Basis Acryldispersion zur Abdichtung von Anschluss- und Bauteilfugen. Schnellregenfest. 2H Acryl 250 ist ein hochwertiger schnellregenfester plastischer Einkomponenten-Dichtstoff auf Basis Acryldispersion. Durch Verdunstung der Wasseranteile härtet 2H Acryl 250 zu einem alterungs-, witterungs- und UV-beständigen Dichtstoff aus. Kartuschen á 310 ml Folienbeutel á 310 ml Folienbeutel á 600 ml

50.5002.00 - PVC-Kleber

Syntech Poliurea Primer – Pur SYNTECH POLIUREA PRIMER-PUR is a single-component polyurethane primer with a base of low viscosity solvent, polyurethane resins and special isocyanates that, once applied, form an elastic film that adheres to the substrate. The processing times of this product range from 90 to 120 minutes, based on the percentage of ambient humidity. SYNTECH POLIUREA PRIMER-PUR offers a support for coatings and waterproofing in general. Intermediate adhesion promoter for two-time applications of polyureas, elastomeric products, etc. The surface of the substrate must be dry, properly cleaned, free from any debris and friable or detached parts. All substrates must have a degree of humidity not greater than 5%. The surface temperature during application must be at least +5° C above dew point. If necessary, depending on the surface, the following interventions are recommended: Bush-hammering Milling Sandblasting Shot Blasting Water-blasting Hydro-jet Cleaning Any contamination (water, dirt, dust, etc.) will have to be carefully removed before coating. Mix the product with mechanical stirrer, being sure that the least possible amount of air is incorporated. Prevent the product from coming into contact with air or moisture. When the substrate is ready, apply SYNTECH POLIUREA PRIMER-PUR in the amount needed. Pay attention to the presence of condensate. In certain cases, whilst the product is still wet, complete a dusting of 0.5–0.8 quartz. From 80 to 120 grams of SYNTECH POLIUREA PRIMER-PUR per square metre of surface to be treated. Can 20 kg

Protech Flex Primer A polyurethane bonding primer for preparing the subsequent filling of the joints with single-component polyurethane sealants in a cartridge (Protech Flex or PROTECH SIGILFLEX MONO) or a two-component product (EG 91) on concrete and masonry surfaces. Preliminary reinforcing impregnation of concrete surfaces, forming walls of flooring and roofing joints, prior to sealing it with polyurethane and epoxy-polyurethane sealants. The application surfaces should be clean, free of incrustations, crumbling and non-adhering parts, dust etc. Apply Protech Flex Primer, using a brush with short bristles, on the walls of the joint to be sealed. It is appropriate to provide for the insertion in the joint, whatever its nature and the specific foamed polyethylene kerb Filtene Fondogiunto, of the appropriate size for the joint to be sealed. Approximately 0.02 kg of Protech Flex Primer for every linear metre of joint to be treated. Packaging: 250 grams Kit A+B UM: €/piece

Protech AC-P Paint based on acrylic resins in aqueous emulsion, for interiors and exteriors, protective lamellar structure which, in addition to having an aesthetic effect, allows maximum filling, transpiration and very high resistance to mechanical and chemical light. The high coverage and expandability make this product extremely easy to apply. The special acrylic resins that compose it allow to obtain a film characterized by a rapid insensitivity to water even during the drying phase, with a consequent reduction of the "snail effect" in the event of atmospheric events. Protective and decorative finish painting of walls, facades, concrete products, plasters, masonry, natural stone, porous substrates in general. For old plasters, pay particular attention to the old pre-existing paints, which must be removed by careful scraping and brushing in order to obtain a healthy and non-friable support; then proceed with the application of Protech Fix AC fixative. When applying on new plasters, it is good practice to insulate the base with acrylic insulator or even better with a white or neutral microemulsion fixative. Avoid windy or cold days when applying. Do not apply on fresh or particularly alkaline substrates, respect a minimum carbonation period of at least four weeks. On large surfaces it is recommended to apply product from the same batch and always proceed wet on wet to avoid signs of recovery. Never operate with temperatures below + 5 ° C. Rainy weather, excessive atmospheric humidity and temperatures below + 8 ° C can greatly compromise drying with the possibility of washing off by rainwater even after several days. . DILUTION (by volume with drinking water) BRUSH 1st COAT: 15% a crossed coat or two coats 12-24 hours apart 2nd COAT: 10%. ROLLER 1st COAT: 10% 2nd COAT: 10%. SPRAY (through specific equipment) 1st COAT: 15/25% 2nd COAT: 15/25%. To avoid filming defects, being resin-based products in aqueous emulsion, the application temperature must be between + 5 ° C and + 35 ° C with relative humidity not higher than 60/70%. Do not apply under the direct action of the sun and wind. Do not apply on fresh or particularly alkaline substrates, respect a minimum drying period of the substrate of at least four weeks. It is also advisable for colored, not to use on large surfaces dyed with different production batches as slight differences between batch and batch are technically possible. Please check the color before application as we will not respond to any disputes regarding the shade of the applied product. From 0.20 to 0.30 liters of Protech AC-P for each square meter of surface to be painted. Pail 14 l

Sanafarbe P Breathable, natural, non-toxic paint, for internal and external surfaces, diffusive type, based on lime putty. Mineral-based, active formulation, high natural anti-mildew and anti-condensation capacity, prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. Sanafarbe P has a high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Decorative and internal and external restoration paint. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. A preliminary fixative treatment of the surfaces is always advisable with a consolidating, transparent, Sanaxil Fix primer, based on potassium silicate. The application of Sanaxil Fix can be done by brush, roller or spray: the number of hands required and the dilution ratio with the most suitable water must be determined according to the conditions and absorption degradation of the supports. The admissible dilution range provides for water addition up to a maximum of 1:1 ratio. Apply by brush, roller, spray, in two coats, spaced-apart, one from the other, by about 24 hours. It allows the easy reproduction of traditional finish type: sponging, rubbing, marbling, infilling. Sanafarbe P is dry to the touch after 2 hours, it can be overcoated after 4 hours, while it will be dry in-depth after 8-16 hours. Apply from 0.20 to 0.40 liters of Sanafarbe P per square metre of surface to be painted. Pail 4 l - Pail 14 l

DETAILING & PAINT CORRECTION